Rear raised King Spring Coils to suit Suzuki Vitara 1.6 & 2.0 V6 LWB 1988-03/1998

Kings Springs use high quality, high stress spring steel.
This newer generation steel allows King Springs to further improve many of their existing designs by reducing the amount of steel required in a spring, making it substantially lighter (by approximately 30%) and reducing the solid height therefore increasing travel.
Being of particular benefit at all top levels of Motorsport, this new high stress material was introduced to the leading V8 super car teams (incl. DJR/TP, FTR & NISSAN) in early 2007 giving a hugely successful endorsement of its characteristics & proven durability.
Although considerably expensive, King Springs have introduced this new high stress steel to their passenger car and 4wd designs which benefit the most at no extra cost to the consumer.
All King Springs heavy duty replacement springs are designed to be uprated. The degree of uprating varies between vehicles, but can generally be stated at 20-40%.

Height Options
Many of our springs are designed to cross reference and give various height options on some vehicles. This information is too diversified and complicated to be printed and is often conditional. Please consult our technical staff if specialist height options are requested.
VEHICLE RIDE HEIGHTS (centre hub to guard) An extensive library of vehicle ride heights is being compiled and this information is available to all customers.

Car Coils
Please note: The following height classifications are a generalization only. Degree of lowering can vary between part numbers and vehicles. Spring design i.e. spring rate and vehicle height is relative to market demand. If exacting measurements are required for vehicle ride heights please contact King Springs.

• Front Low: Lowers vehicle approximately 30mm below standard.
• Front STD: Standard Height. Front Raised: Raises vehicle approximately 20mm above standard (recommended for bull bar, country driving or whenever increased ground clearance is desired).
• Rear Low: Lowers vehicle approximately 30mm below standard.
• Rear STD +:Standard height to 20mm raised.
• Rear Raised: Raises vehicle approximately 30-40mm above standard (recommended for excessive towing, load-carrying or LPG tank etc)

NOTE: Super Low coils are generally 40-50 below standard.

4WD & Ford "F" Series Coils

• Front and Rear STD: Raises vehicle approximately 10mm-20mm above standard.
• Front and Rear RAISED: Raises vehicle approximately 30mm-40mm above standard.

Note: All heights mentioned are a generalisation only. Vehicle ride heights can vary, depending on:

• Life and/or age of vehicle
• Accessories fitted to the vehicle
• Factory options (Country Pack, S Pack etc.)

When discussion vehicle ride heights, consider all of the above and advise customers accordingly.
LPG - For cars fitted with LPG tanks use part No. in Raised column to sit Std. Height.

Measuring Coil Springs
Listed below is relevant information required when identifying or measuring coil springs.

• Free Length: The length of the coil at it's longest point out of the vehicle not under load. To measure, lay coil flat, butt one end to flat surface at right-angles with coil.
• Open Strut Length/Trapped Length: The length of the coil when vehicle body is jacked up and all load is removed from spring (except pre-load).
• Static Length: The length of the coil in the vehicle as it stands under normal load.
• Inside Diameter: The width of the spring at it's widest point from inside edge to inside edge. Note: Check both ends, as many coils can reduce at one end only or be conical in design.
• Total Coils: The total number of complete turns from start to finish (including reductions if any).
• Material Diameter: (Check with verniers) Note: Check end coils as diameter may decrease.

End Configuration: There are several types of end finishes:

• Normal: (not ground, straight cut) Note: Measure end gap at tip to next coil (FWO-)or (FWC-)
• Ground: Ground flat (TWC-)
• Pigs Tail: End reduces greatly and will fit inside the coil below (PT-)
• Reduced: End coil will sit on top of coil below. (RED-)

Trouble Shooting (Coil and Leaf Springs)

• Kings Performance Replacement Coil Springs in both STD and Raised Heights are often shorter than the springs they are replacing. This is because they don't compress as far under the initial pre-load or weight on the vehicle.
• When sorting vehicle height problems, be sure that all wheel and tyre sizes and type pressures are compatible. Measure all four corners. Measure centre hub to guard, with vehicle on flat surface. NOTE: Most vehicles transfer weight diagonally.
• Many Part numbers listed in the catalogue have a driver's side and passenger side and are marked accordingly.
• Wheel alignment is recommended after having front springs fitted on all vehicles. Some vehicles require wheel alignment on rear when rear springs are fitted. Refer wheel alignment specialist.
• Allow 4WD Leaf Springs settling time of approximately 500klms then check and re-tighten all U-bolts and Shackles.

Product Stock

Please be advised that our stores do not hold any stock. In order to make sure things go as fast as possible you can purchase your parts online. If you would like to have your parts installed by us please choose Click & Fit at the checkout.

You can use the shipping calculator to find your shipping costs, your closest pick up or install locations. The shipping calculator will also show all shipping and installation prices. Shipping is free if you choose to get your item installed by us.

When our product stock levels are low, or current stock is allocated to orders, our website may show an ‘in-stock’ status when in fact the item might be sold out. We will advise within 48hrs; stock availability, order status and shipping details.

Delivery Methods

1. Select “Click & Fit” as a delivery method during the checkout process and you will be given a special fitted price to have both the product delivered and installed. A suspension expert will be assigned to your order, who will organise everything for you and will help you every step of the way. You can sit back and relax, knowing that your car is going to be looked after by suspension experts.

2. Select “Free Pickup” as a delivery method during the checkout process and you will be given free delivery to your nearest Fulcrum outlet where you can collect the parts. We will text and email you all your tracking details. 

3. Select “Deliver to Door” as a delivery method during the checkout process and we will deliver your order direct to your nominated delivery address. We will text and email you all your tracking details. 

Shipping

We offer FREE shipping to all metro areas (excluding WA, TAS and NT).

If you live on the Australian coast, that does not mean you are subject to free shipping.

Express shipping times and free shipping times are only to be counted once the order has been shipped from our warehouses. Our free shipping and express shipping services both have the same order processing times. We first have to raise the order, then we send it to one of our warehouses for processing and once ready it will be shipped from the warehouse. The difference between express and free shipping services, is the time it takes for the item to be transported from our warehouse to your address.

Our free shipping policy is determined by densely populated metro locations and the viability of distance travelled from our distribution centres. We are constantly expanding our warehousing, so areas covered by free shipping are subject to change. See our shipping policy here.

Returns

We guarantee the fitment and quality of our products, but if you choose to return an item we offer a generous 60 day returns policy. See our returns policy here.

Warranty

All products sold by Fulcrum Suspensions are covered by a national warranty. This products warranty is subject to conditions from the date of purchase, unless otherwise stated on the item.

Warranty claims must meet certain criteria and be sent to Fulcrum Suspensions with a receipt to be eligible for a refund. See full warranty claim criteria here.